Atom transfer radical polymerization of methyl methacrylate by copper(I)‐pyridine‐2‐carboximidate catalysts

Pyridine‐2‐carboximidates [methyl ( 1a ), ethyl ( 1b ), isopropyl ( 1c ), cyclopentyl ( 1d ), cyclohexyl ( 1e ), n‐octyl ( 1f ), and benzyl ( 1g )] were prepared from the reaction of 2‐cyanopyridine with the corresponding alcohols. Cyclopentyl‐substituted 1d was found to be a highly effective ligand for copper‐catalyzed atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA). For example, the observed rate constant for a CuBr/ 1d catalytic system was found to be nearly twice as high as the cyclohexyl‐substituted CuBr/ 1e catalytic system [k_obs = (1.19 vs 0.56) × 10^?4 s^?1). The effects of the solvents, temperature, catalyst/initiator, and solvent/monomer ratio on the ATRP of MMA were studied systematically for the CuBr/ 1d catalytic system. The optimum condition for the ATRP of MMA was found to be a 1:2:1:400 [CuBr]_o/[ 1d ]_o/[ethyl 2‐bromoisobutyrate]_o/[MMA]_o ratio at 60 °C in veratrole solution, which yielded well‐defined poly(MMA) with a narrow molecular weight distribution of 1.14. The catalytically active copper complex 2d was isolated from the reaction of CuBr with 1d . Narrow molecular weight distributions as low as 1.06 were achieved for the CuBr/ 1d catalytic system by employing 10% of the deactivator CuBr₂. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2747–2755, 2004     

Effects of the copolymer microstructure on the morphology of polyethylene–poly(ethylene‐co‐α‐olefin) blends

The effects of the copolymer microstructure on the morphology evolution in polyethylene/poly(ethylene‐co‐α‐olefin) blends were investigated. Microscopy revealed that the melt‐phase morphology, inferred from the solid‐state morphologies of annealed and quenched samples, was strongly affected by the copolymer structure, that is, the branch content and branch length. Higher molecular weight α‐olefin comonomer residues and residue contents in the copolymers led to faster coarsening of the morphology. The molecular weight of the polyethylene and the copolymers affected the coarsening rates of the morphology, principally through its influence on the melt viscosity. The effects of the molecular weight were largely explained by the normalization of the coarsening rate data with respect to the thermal energy and zero‐shear‐rate viscosity. Thus, the effect of the molecular weight on the compatibility of the blends was much smaller than the effects of the branch length and branch number. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 965–973, 2004     

Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004     

Behavior of cellulose in NaOH/Urea aqueous solution characterized by light scattering and viscometry

Cellulose was dissolved in 6 wt % NaOH/4 wt % urea aqueous solution, which was proven by a ¹³C NMR spectrum to be a direct solvent of cellulose rather than a derivative aqueous solution system. Dilute solution behavior of cellulose in a NaOH/urea aqueous solution system was examined by laser light scattering and viscometry. The Mark–Houwink equation for cellulose in 6 wt % NaOH/4 wt % urea aqueous solution at 25 °C was [η] = 2.45 × 10^?2 weight‐average molecular weight (M_w)^0.815 (mL g^?1) in the M_w region from 3.2 × 10⁴ to 12.9 × 10⁴. The persistence length (q), molar mass per unit contour length (M_L), and characteristic ratio (C_∞) of cellulose in the dilute solution were 6.0 nm, 350 nm^?1, and 20.9, respectively, which agreed with the Yamakawa–Fujii theory of the wormlike chain. The results indicated that the cellulose molecules exist as semiflexible chains in the aqueous solution and were more extended than in cadoxen. This work provided a novel, simple, and nonpollution solvent system that can be used to investigate the dilute solution properties and molecular weight of cellulose. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 347–353, 2004     

Cl/HN3/I2全气相化学激光体系的化学动力学模拟计算

 对Cl/HN₃/I₂产生NCl(a)/I激光的过程进行了化学动力学计算，主要考察了Cl,HN₃和I₂的初始粒子数密度及其配比对小信号增益系数的影响。结果发现,当温度为400K, 初始Cl粒子数密度为1×10¹⁵，1×10¹⁶和1×10¹⁷cm^-3时,小信号增益系数分别达到1.6×10^-4,1.1×10^-3和1.1×10^-2cm^-1，获得最佳小信号增益系数的HN₃和I₂的初始粒子数密度分别为初始Cl粒子数密度的1～2倍和2%～4%。同时，对Cl，HN₃和I₂配比对小信号增益系数和增益持续时间的影响进行了讨论。     

Two-Layered Poly-o-phenylenediamine/Polyaniline Composite: Electrosynthesis and Spectroelectrochemical Properties

Spectroelectrochemical properties of poly-o-phenylenediamine (PPD) and the synthesized composite of PPD and polyaniline—two chemically related polymers containing an amino-substituted benzene ring but having different conduction nature—are studied. The polyaniline synthesis on PPD-modified electrodes involves stages of the reaction initiation, the copolymer formation, and the formation of a polyaniline layer at the copolymer/solution interface.     

Acetalation and Ketalation Catalyzed by SO42-/TiO2-MoO3

The catalytic activities of SO42-/TiO2-MoO3 in synthesizing cyclohexanone ethylene ketal,cyclohexanone 1,2-propanediol ketal, 2-propyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane,2-isopropyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane, butanone ethy-lene ketal and butanone 1,2-propanediol ketal were reported. It has been demonstrated that SO42-/TiO2-MoO3 is an excellent catalyst. Various factors concerned in this reaction have been investigated. The optimum conditions have been found, that is, the molar ratio of aldehyde/ketone to alcohol was 1:1.5 or 1:1.3,the mass ratio of the catalyst used to the reactants was 0.25～1.5%, and the reaction time was 45～60 min. Under this conditions, the yield of cyclohexanone ethylene ketal is 82.7%, cyclohexanone 1,2-propanediol ketal is 83.4%, the yield of 2-propyl-1,3-dioxolane is 68.1%,4-methyl-2-isopropyl-1,3-dioxolane is 87.5%, the yield of 2-isopropyl-1,3-dioxolane is 70.7%,4-methyl-2-isopropyl-1,3-dioxolane is 82.5%, the yield of butanone ethylene ketal is 74.1%, and butanone 1,2-propanediol ketal is 94.9%.Some equation and experiment results concerned of the synthetic acetals or ketals were listed as follows.     

Synthesis And Properties Of Functional Ultra-High Molecular Weight Transparent Styrene-Butadiene Block Copolymer

Functional ultra-high molecular weight transparent styrene-butadiene block copolymer possesses both high transparency and impact resistance and has excellent comprehensive properties prior to other transparent resins. In this paper we not only use anionic polymerization process which includes 1 time addition of initiator and 3 time addition of monomers, but also introduce functional coupling agent for the fist time to prepare mentioned functional block copolymer. The typical preparation proces…     

Hydrothermal Synthesis and Characterization of a Novel Two-dimensional Framework Materials Constructed from Polyoxometalate and Coordination Groups: [H_2Mo_(5.5)V_(10.5)O_(40)(PO_4)][Cu(en)_2]_4·7H_2O

IntroductionPolyoxometalatesarewidelystudiedfortheirin terestingapplicationsincatalysis ,electronicconduc tivity ,magnetism ,nonlinearopticsandmedicine[1— 4 ] .Whilethemechanismofthesynthesisofpolyoxometalatesremainselusiveandisoftende scribedasself assembly ,thereseemstobeanincreas inguseofthecombinationofthehydrothermalmethodandthestructure directingtemplate .There searchwiththismethodhasdemonstratedthatanum beroftransitionmetaloxides ,typicallyreducedmolybdenumoxides ,mixedvalancevanadiumo…     

Self-assembly of Carboxyl Functionalized Polystyrene Nanospheres into Close-packed Monolayers via Chemical Adsorption

The polyacrylic acid functionalized polystyrene nanospheres were synthesized and self-assembled into irregular, densely packed monolayers in non-aqueous media. The polymer nanoparticles were chemically adhered to substrates. The morphologies of the resulting films were investigated. The impact of the volume fraction of alcohol in the mixed solvents on the particle adsorption and fabrication of nanosphere assembled films was examined.